Corn Extruder Machine-manufacture,factory,supplier from China

The screw extruder was first used in the plastics industry, and its theoretical research started earlier, forming a variety of mathematical models used to describe the basic principles of flow and heat transfer in the extrusion process, using these models to achieve accurate extrusion machine simulation Design. The application of extrusion technology in the food industry is slightly later than that in the plastics industry, which is mainly due to the complexity of food raw materials.

1. Before operating the corn equipment bulking machine, remove the head, movement, lead screw and other parts, clean them up, dry them and then install them.2. Idling for 1 to 2 minutes first when operating, put the raw materials into the feed mouth, not too fast, when the ring groove of the spiral shaft head is filled, stop feeding, friction preheating. Wait until the nose temperature rises and the pressure inside the cabin builds up before feeding.3. Feed should be continuous and uniform, material must be dry, must pay attention to.4.

Twin screw extruder is developed on the basis of single screw extruder. Two screws are placed side by side in the barrel of the twin screw extruder. According to the meshing degree of the two screws can be divided into mutual meshing type and non-meshing type. According to the rotation direction of the two screw shafts, it can be divided into reverse rotation type and co-rotation type.(1) meshing twin screw: Because the meshing gap of the meshing screw is very small, the material has the ability of forced conveying, not easy to produce backflow, leakage phenomenon.

TYPES OF CAT FOODCat food comes in a variety of shapes and textures, but can be broadly divided into four based on moisture content and manufacturing methods.*Heating foaming process: Using an extruder called an extruder, the mixed raw materials are heated and pressurized to 120 to 160 degrees.Characteristics and production methods of dry foodFEATUREDry food has the following characteristics.Moisture below 10%excellent preservationA nutritionally complete diet with high-efficiency and easily ingested nutrientsMoisture below 10%It has the lowest moisture content of the four and has a crunchy te

As a food processing equipment, the food extruder has many precautions in use. For example, we need to remove the machine head, movement and lead screw before starting the operation, and we must carefully clean the rice on the machine. dirt and oil, and then re-installed. Only in this way can the material reach the required state and quality. So in the process of Jinan puffing extrusion equipment operation, what should we pay attention to?Matters needing attention during the operation of the extruder are:1. Mainly use corn and potatoes as raw materials to produce small food.2.

There is only one screw in the barrel of the single screw extruder, it is by the friction of the screw and the barrel of the material to transport materials and form a certain pressure. In general, the friction coefficient between the material and the barrel is greater than that between the material and the screw. Otherwise, the material will be wrapped in the screw together to rotate and not play the role of forward propulsion.Screw is divided into three sections: feeding (feeding) conveying section, compression melting section, metering homogenization section.

Extruder belongs to a kind of equipment for processing puffed food. It is a kind of equipment for processing puffed food, such as processing rice, corn, soybean, wheat, etc., in daily life.

How it worksObviously, the material will flow from the high pressure area to the low pressure area in two directions: one is that the wear of the square screw will be reduced as the screw rotates, and the material will be transported, sheared, mixed and heated by the barrel shell in this way.Under the action of high pressure, it is matured and then squeezed out of the cylinder.The counter-rotating twin-screw extruder generally uses two screws with the same size but opposite thread directions.

What is the composition of the extruderThe extruder mainly consists of an extrusion device, a transmission device, a feeding device, a motor, a discharging device and a machine base. The main device is the screw rod mechanism in the extrusion device: the taper hollow shaft, the screw blade. The drive device is a three-phase asynchronous motor, and the motor is connected with the screw shaft by a coupling.

Working Principle of Twin Screw ExtrusionAfter a certain amount of pulverization, the material with a certain water content is fed into the extruder cavity, so that the material will undergo mixing, shearing, A series of complex continuous processes such as melting, curing and sterilization. Because there is a certain air pressure difference inside and outside the barrel, the moment the material is extruded, the external pressure it is subjected to is reduced to normal pressure, so that the material is instantly puffed.